No products
Product added to your shopping cart
There are 0 items in your cart. There is 1 item in your cart.
Aircraft
- Electronics
- Battery
- Buzzers
- Cable
- Capacitors
- Circuit Boards
- Circuit Breakers
- Coils/Inductors
- Connectors
- Cord, Power
- Counters
- Crystals
- Digital ICs
- Diodes
- Enclosures
- Fans/Blowers
- Filters
- Fluorescent
- Fuse
- Grounding
- Hardware
- Heat Sinks
- Heating Elements
- Inductor
- Instruments
- Lamps/Sources
- Meters
- Miscellaneous
- Motors
- Optoelectronics
- Panels
- Plugs/Outlets
- Potentiometers
- Power Supply
- Products
- Rectifiers
- Regulators
- Relays
- Resistors
- Sensors
- Solenoids
- Speakers
- Suppressors
- Surge Arresters
- Switches
- Tape
- Testers
- Thermocouples
- Thermostats
- Timers
- Transformers
- Transistors
- Trimmers
- Tubes Electronic
- Wire
- Hardware
- Anchors
- Bearings
- Belts
- Bolts
- Braces
- Bumpers
- Bushings
- Catches
- Chain
- Clamps
- Collars
- Dampner
- Door Bells
- Door Stops
- Dowels
- Fittings
- Gears
- Handles
- Handrails
- Hasps
- Hinges
- Hooks
- Hose Clamps
- Knobs
- Latches
- Leveler
- Lever
- Locks
- Magnifying Glass
- Mounting
- Nails
- Nuts
- O-Rings
- Pipe Support
- Pulleys/Sheaves
- Pulls
- Rivet
- Rollers
- Screws
- Shafts
- Shelving
- Slides
- Springs
- Sprockets
- Standoffs/Spacers
- Staples
- Straps
- Strike Plates
- Strut System
- Tacks
- U-Bolts
- Upholstery
- Valves/Fittings
- Wall Hangers
- Wall Plates
- Washers
- Industrial Items
- Odds & Ends
- Office Items
- Photo, Film, A/V
- Tools
Information
For convenience,
products are pictured
on a 1" x 1" grid.
There are 49 products.Aircraft
USED Taper-Lok Cutter Countersink 0066-406 HS 225609USED, previously owned by retired machinist, no spec sheet, life cycle unknown although cutting edges still look and feel sharp, missing original packaging. Listing is for one (1) each taper-lok cutter with countersink, primarily used in aircraft construction for producing finished holes for taper-lok fasteners, for use in previously drilled/punched...
$13.811 in stock$13.81
USED Taper-Lok Cutter Countersink 0066-506 222003 HSUSED, previously owned by retired machinist, no spec sheet, life cycle unknown although cutting edges still look and feel sharp, missing original packaging. Listing is for one (1) each taper-lok cutter with countersink, primarily used in aircraft construction for producing finished holes for taper-lok fasteners, for use in previously drilled/punched...
$13.811 in stock$13.81
USED Taper-Lok Cutter Countersink 0065-404 HS 263673-2USED, previously owned by retired machinist, no spec sheet, life cycle unknown although cutting edges still look and feel sharp, missing original packaging. Listing is for one (1) each taper-lok cutter with countersink, primarily used in aircraft construction for producing finished holes for taper-lok fasteners, for use in previously drilled/punched...
$11.654 in stock$11.65
USED Taper-Lok Cutter Countersink SPT-29-32-015513-TD HSUSED, previously owned by retired machinist, no spec sheet, life cycle unknown although cutting edges still look and feel sharp, missing original packaging. Listing is for one (1) each taper-lok cutter with countersink, primarily used in aircraft construction for producing finished holes for taper-lok fasteners, for use in previously drilled/punched...
$8.571 in stock$8.57
Filters
